Aerobed Sleep Basics Elevated Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Meubles Aerobed Sleep Basics Elevated. AeroBed Sleep Basics Elevated User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
8085 Rev 12/09
Pump HB177/Hi805AB
Instruction Manual
IMPORTANT SAFETY INFORMATION AND WARNINGS
SAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
IMPORTANT: Preparation of your product requires no tools. Use of tools may damage your bed.
WARNING: This is an electrical product – not a toy. To avoid risk of fire, burns, injury, or shock:
- Always unplug from outlet when not in use and before cleaning.
- Close supervision is necessary when this product is used by or near children, invalids, or disabled persons.
- Use this product only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
- Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water.
- Keep the cord away from heated surfaces.
- Never operate the product with the air openings blocked. Keep the air openings free of lint, hair, and the like.
- Never drop or insert any object into any opening.
- To disconnect, turn all controls to off position, then remove plug from outlet.
WARNING: Product is for indoor use only. Do not use outdoors. For household / residential use only.
WARNING: This furnishing has not been evaluated for flammability or cigarette ignition resistance.
ADDITIONAL WARNINGS:
- Bed supports a maximum weight of 300 lbs. per person.
- This is not a water toy. Use as a mattress only.
- This bed is not designed for use by children under 3 years of age or any persons with limited mobility as they could suffer
serious or fatal injury through suffocation, falling from or rolling off the bed or becoming trapped.
- Use on flat surfaces only. Bed may tip over on uneven surfaces.
- Inflate bed fully. Partially inflated mattresses can cause suffocation.
- Remove all sharp objects from area where bed will be set up and used. Do not use this bed on abrasive surfaces or near
pointed/sharp items or surfaces. Bed may puncture.
- Do not step or jump on bed or use as a trampoline.
- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place
it near or against heaters, open flame, or other hot objects.
- Pump is not intended for continuous use. Pump may stop working or overheat if it is used for extended periods of time.
Do not use pump continuously (refer to warning statement on side of pump).
To avoid excessive heat build-up in the pump, let it rest for 10 minutes between complete inflation cycles.
- Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained inside.
Contact Aero Products International, Inc. at 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173, 1-888-462-4468
for repair or servicing information.
A REPAIR PATCH CAN BE ORDERED AT WWW.AEROBED.COM OR BY CALLING OUR CUSTOMER SERVICE AT 1-888-462-4468.
Thank you for joining the AeroBed
®
family by purchasing one of our products. You can expect top-notch quality, innovation and imagination from every AeroBed product.
You are about to enjoy the comfort of an AeroBed product. It is your responsibility to read and always follow the safety, care and maintenance instructions for your new
AeroBed product. Always instruct and supervise others on your bed’s proper use, maintenance and safety.
INFLATION
Note: Product must be at room temperature prior to inflating or it may cause air leaks.
1. Place your rolled up bed on the floor or other surface free of obstructions or sharp objects.
2. Remove pump from protective plastic shipping wraps.
3. Open protective cap on valve by turning counter-clockwise (see figure A). Attach universal adapter to pump inflation port by
pushing until it locks into the end (see figure B). Press the smaller end of adapter into mouth of valve, then turn pump to “on” position.
4. In approximately 3 minutes, your bed will be inflated to the firmest capacity. Detach pump and close valve by turning clockwise.
Turn pump to “off” position.
5. Lie on bed and check the firmness. If you want the bed to be firmer, open protective cap by turning counter-clockwise.
Press the smaller end of adapter into the mouth of valve, reinflate the bed until the desired level of firmness is achieved.
6. Replace valve cap.
DEFLATION AND STORAGE
1. To deflate your AeroBed, open the valve located next to the pump (see figure D). Deflation takes approximately 90 seconds.
2. For most compact storage, open protective cap by turning counter-clockwise. Attach universal adapter to pump deflation port
on top of pump (see figure C).
3. Press the smaller end of adapter into mouth of valve and then turn pump to “on” position.
4. Your bed will begin to deflate, once deflated turn pump to “off” position.
5. Roll the bed completely until all the air is expelled. When the bed is completely rolled, replace the valve cap by turning clockwise.
6. Fold sides of bed into the center along its length (see figure E). Tightly roll and place in convenient carry bag for easy transport and storage.
UNIVERSAL ADAPTERS
For use with other air-filled products.
1. Attach universal adapter to end of pump by pushing until adapter locks into position.
2. Additional adapters are included for use with multiple sized valve openings.
3. Use pump with other products.
4. Discharge pump and store for next use.
A
B
C
D
E
Vue de la page 0
1 2

Résumé du contenu

Page 1 - Instruction Manual

8085 Rev 12/09Pump HB177/Hi805ABInstruction ManualIMPORTANT SAFETY INFORMATION AND WARNINGSSAVE THESE INSTRUCTIONSREAD AND FOLLOW ALL INSTRUCTIONS BEF

Page 2

LIMITED EXPRESS WARRANTYAero Products International, Inc. (“us”) warrants to the original purchaser (“you”) that the AeroBed (“product”) is guaranteed

Commentaires sur ces manuels

Pas de commentaire